Car Key Button Repair

A broken car keys repair near me key can be a hassle. It is possible to call an emergency locksmith service or purchase an alternative remote.

But, you may be in a position to save money by repairing an old key fob instead of replacing it. This is especially true if the problem is due to an old switch or a damaged contact.

Battery

If the buttons on your key fob don't respond to pressing the buttons, this could be a clear sign that the battery is dying or nearing the end of its life. Fortunately, replacing the battery is a simple task that can be done on your own rather than hiring a locksmith to take care of it.

Find the battery compartment first. It is typically located on the backside of the key fob and could be hidden behind an open cover that slides out or an access point that opens when you push the button. Once the compartment is exposed you can see the small button battery. This is typically shaped like an oblong coin and is identified with the plus and minus signs. Take the battery out and Car Key Button Repair insert a new one in its place, making sure that the plus and minus signs are correctly aligned.

Close the compartment and snap the two parts of your key fob. Before closing the door make sure to align and snap the components into the correct position. Press any of the buttons to verify that they function properly.

If your remote key fob stops working after replacing the battery, it may be experiencing other issues that require a different kind of repair keys near me. Dropping the device in a puddle could cause it to stop functioning. It could also be experiencing an internal electrical failure or might need to be deprogrammed by an expert or locksmith. Also, take a look at these common auto troubleshooting techniques to determine whether your key fob may be suffering from a different issue.

Switches

Based on the year and make, there are different types of switches on the keyfob of your car. The older type of key usually has an additional chip that is visible inside the case, whereas modern keys are more sophisticated and function by sending signals to the car. Regardless of the type, the buttons on the key can be damaged or worn out during normal use. They become hard to press or ineffective. If you attempt to force the button to work, it can cause further damage, and could even prevent the key from starting your vehicle in the future.

If you can't get your key to function, try changing the batteries. If this doesn't work, you might need to clean your key's fob or re-adjust its switches. Because these tiny electronic switches are constantly being tossed around, they are more likely to wear out than larger parts of your key.

The switches are rubber-like, and they're coated with an electricity conducting film that wears down over time. They're fortunately a very small part and cheap to replace. The older ones are soldered to the circuit board, and you'll need to be careful to remove them without causing any damage to anything else. Then, you can solder in the new ones and put them back together.

Avoid using your car key fob for more than an hour at a time, and do not leave it open. If you don't use your key, put it away in a secure location.

If the problem persists after you've cleaned the key fob or battery, and tried to clean it, then you might need to contact a locksmith. A professional locksmith can check your key's frequency to see whether your car is able to communicate. They can also open and replace microswitches, alter cases, and much more.

Outer Case

A key fob spends a lot of time jostled around, and if the buttons aren't free to move upwards and downwards within the case, they may become stuck or even broken car key repair. If cleaning the case using rubbing alcohol and a cotton swab does not work, it might be necessary to take off the case. If the contacts that the buttons touch aren't a good fit or if they're damaged, adjusting them could be the only solution.

Rubber buttons can be worn out over time. The buttons made of rubber can become difficult to press when they stretch, and nails may cut them. This can cause the key to fail, and in this case it's time for the replacement of the case or buttons. This repair involves removing the remote, finding the button switches on the circuit board, then heating the solder and carefully taking them off. The circuit board is then soldered with new buttons. The case can be rebuilt and the horseshoe key blade can be inserted. The new buttons must be snugly fitted into the case in order to stop them from falling out.

Inner Case

Since your key fob is likely to be tossed around and could occasionally be pressed by accident and the buttons within can get damaged or stuck over time. Using metal tape and a hole punch you can fix this problem in the event your car is not at home and the key fob won't work and allows you to open the doors, but not to start the engine. This simple fix can allow you to return safely to your vehicle to complete your journey.